Re: [sap-log-mm] Rounding off stock in migo
Posted by
Admin at
|
Share this post:
|
|
0 Comments
 | Posted by rajnikant-vadhwana on Feb 15 at 11:27 PM |  Mark as helpful |
Hi All,
Thanks for valuable suggections.
________________________________
From: Keith Lewis via sap-log-mm <sap-log-mm@Groups.ITtoolbox.com>
To: rajnikant-vadhwana <rajnikant_0109@yahoo.com>
Sent: Mon, 15 February, 2010 2:47:57 PM
Subject: RE: [sap-log-mm] Rounding off stock in migo
Posted by Keith Lewis (Senior SAP Logistics Analyst)
on Feb 15 at 4:21 AM Mark as helpful
The only way I can think of which you may be able to do this is to
change the Unit of Measure config (and even then I'm not 100% sure that
it would work correctly). If you really don't want any decimal places to
be received you could try changing the config of the LT unit of measure
so that is has 0 decimal places, but please be aware that this would
affect that unit of measure in the WHOLE system, not just for this
specific scenario so only do it in your DEV system until you have tested
it 100% in all areas of the system.
Cheers
Keith
Keith Lewis
Senior SAP Logistics analyst
Smith & Nephew Endoscopy
Endoscopy House
Cardinal Park
Cardinal Way
Godmanchester
Huntingdon
PE29 2SN
E: keith.lewis@smith-nephew.com <mailto:keith.lewis@smith-nephew.com>
T: +44 (0)1480 423237 direct
T: #1415 3237 (IP phone)
F: +44 (0)1480 423201
M: +44 (0)7951 986 300
This electronic transmission is strictly confidential to Smith & Nephew
and intended solely for the addressee. It may contain information, which
is covered by legal, professional, or other privilege. If you are not
the intended addressee, or someone authorized by the intended addressee
to receive transmissions on behalf of the addressee, you must not
retain, disclose, in any form, copy or take any action in reliance on
this transmission. If you have received this transmission in error,
please notify us as soon as possible and destroy this message.
________________________________
From: vinod_s via sap-log-mm [mailto:sap-log-mm@Groups.ITtoolbox.com]
Sent: 12 February 2010 19:15
To: Lewis, Keith
Subject: Re: [sap-log-mm] Rounding off stock in migo
Posted by vinod_s (MM WM
Consultant)
on Feb 12 at 2:30 PM
Mark this reply as helpfulMark as helpful
<http://it.toolbox.com/api/ContentVote/3304105/1/1/>
Hi Rajnikant,
Standard SAP would always convert the PO unit into base unit of measure
and it will convert upto 3 decimal point. I dont think there is any
config to trunc off the decimal points. However you can do a small
developmengt using USER EXIT and this can be solved. Please check with
your ABAP guy.
thnx
--
Click for exclusive coverage on the New Bajaj Pulsar 220 the fastest
Indian bike
http://www.zigwheels.com/Features/Bajaj-Pulsar-220-DTSi-Special-Coverage
/Pulsar_20090623-1-1
__.____._ Thanks for valuable suggections.
________________________________
From: Keith Lewis via sap-log-mm <sap-log-mm@Groups.ITtoolbox.com>
To: rajnikant-vadhwana <rajnikant_0109@yahoo.com>
Sent: Mon, 15 February, 2010 2:47:57 PM
Subject: RE: [sap-log-mm] Rounding off stock in migo
Posted by Keith Lewis (Senior SAP Logistics Analyst)
on Feb 15 at 4:21 AM Mark as helpful
The only way I can think of which you may be able to do this is to
change the Unit of Measure config (and even then I'm not 100% sure that
it would work correctly). If you really don't want any decimal places to
be received you could try changing the config of the LT unit of measure
so that is has 0 decimal places, but please be aware that this would
affect that unit of measure in the WHOLE system, not just for this
specific scenario so only do it in your DEV system until you have tested
it 100% in all areas of the system.
Cheers
Keith
Keith Lewis
Senior SAP Logistics analyst
Smith & Nephew Endoscopy
Endoscopy House
Cardinal Park
Cardinal Way
Godmanchester
Huntingdon
PE29 2SN
E: keith.lewis@smith-nephew.com <mailto:keith.lewis@smith-nephew.com>
T: +44 (0)1480 423237 direct
T: #1415 3237 (IP phone)
F: +44 (0)1480 423201
M: +44 (0)7951 986 300
This electronic transmission is strictly confidential to Smith & Nephew
and intended solely for the addressee. It may contain information, which
is covered by legal, professional, or other privilege. If you are not
the intended addressee, or someone authorized by the intended addressee
to receive transmissions on behalf of the addressee, you must not
retain, disclose, in any form, copy or take any action in reliance on
this transmission. If you have received this transmission in error,
please notify us as soon as possible and destroy this message.
________________________________
From: vinod_s via sap-log-mm [mailto:sap-log-mm@Groups.ITtoolbox.com]
Sent: 12 February 2010 19:15
To: Lewis, Keith
Subject: Re: [sap-log-mm] Rounding off stock in migo
Posted by vinod_s (MM WM
Consultant)
on Feb 12 at 2:30 PM
Mark this reply as helpfulMark as helpful
<http://it.toolbox.com/api/ContentVote/3304105/1/1/>
Hi Rajnikant,
Standard SAP would always convert the PO unit into base unit of measure
and it will convert upto 3 decimal point. I dont think there is any
config to trunc off the decimal points. However you can do a small
developmengt using USER EXIT and this can be solved. Please check with
your ABAP guy.
thnx
--
Click for exclusive coverage on the New Bajaj Pulsar 220 the fastest
Indian bike
http://www.zigwheels.com/Features/Bajaj-Pulsar-220-DTSi-Special-Coverage
/Pulsar_20090623-1-1
Copyright © 2010 Toolbox.com and message author.
Toolbox.com 4343 N. Scottsdale Road Suite 280, Scottsdale, AZ 85251
Toolbox.com 4343 N. Scottsdale Road Suite 280, Scottsdale, AZ 85251
Related Content
In the Spotlight
White Papers
In the Spotlight
Earn Recognition for Your Contributions at Toolbox for IT. Gain Points for Community Achievements
View this thread online
Manage group e-mails
Create an FAQ on this topic
Tell us what you think
Unsubscribe from discussion
Manage group e-mails
Create an FAQ on this topic
Tell us what you think
Unsubscribe from discussion
